- #SSD FOR MAC AIR 2013 FULL#
- #SSD FOR MAC AIR 2013 PRO#
- #SSD FOR MAC AIR 2013 PLUS#
- #SSD FOR MAC AIR 2013 WINDOWS#
Once the installation finishes, the computer will boot into macOS and you can restore your old files from the backup you made before starting. Select your freshly formatted NVMe SSD as the installation drive and macOS will be installed to the new drive. After the drive has finished formatting, quit the Disk Utility app and select “Install macOS” from the menu. Click “Erase” then select APFS as the format and “GUID Partition Map” as the scheme. Open the Disk Utility app from the menu and select your NVMe SSD in the pane to the left. 
Once the USB has booted, it’s time to format the drive.From the boot screen that appears, choose the USB drive.
Plug your bootable macOS installation USB into a USB port and turn on the Mac while holding the Option key. Replace the bottom case, putting the screws back in the same place you removed them from (they may look the same but they’re actually different sizes). Reconnect the battery to the motherboard and replace the plastic tape. It should be screwed in firmly enough to hold it in place but not over-tightened. Be careful not to screw it in too tight as it could cause the SSD to bend. Gently screw the drive into place using the screw provided with the adapter. It should be inserted at an angle of around 30 degrees. Insert the adapter and the SSD into the slot on the motherboard. The screw hole on the SSD should align with the one on the adapter. Fit your new SSD into the adapter, making sure that it’s fully inserted in the slot. Using your Torx T5 screwdriver, remove the screw securing the SSD and slide the SSD from its socket. With the battery nearest you, you should see the SSD at the rear of the motherboard, on the right. Peel up the black tape covering the battery connector and disconnect the battery from the motherboard using a plastic prying tool or your fingernail. #SSD FOR MAC AIR 2013 PRO#
MacBook Pro 13″ Lower Case screw locations Once all screws are removed, lift off the bottom plate.
Turn the MacBook Pro face down on the desk and, using your Pentalobe screwdriver, carefully remove the screws on the bottom. Create a bootable USB installer of macOS following these instructions from Apple. You can copy this back to the new drive after installing macOS. 
This ensures that the EFI firmware in your Mac is updated to the latest version with NVMe support.Īlso, to be safe, make a backup of your data and important files to an external drive. Make sure that you have upgraded your Mac to Mojave or later with the original drive installed before beginning.
A MacBook Pro or MacBook Air from late 2013 onwards (not USB-C models) that has been updated to macOS Mojave or later. A Torx T5 screwdriver, to remove the screw securing the SSD and slide it out of the slot. A Pentalobe screwdriver is needed to remove the screws on the base of the MacBook Pro. Some of the best NVMe SSD’s currently available, with tested macOS compatibility, are the Samsung 970 EVO, the Samsung 970 PRO, the Sandisk Extreme and the WD Black. #SSD FOR MAC AIR 2013 PLUS#
Note that certain SSD’s have compatibility issues with macOS – including the Samsung PM981 and the Samsung 970 EVO Plus (the original 970 EVO works fine, though). A USB memory stick of at least 8GB capacity, to use for installation of macOS on the new SSD.
#SSD FOR MAC AIR 2013 FULL#
This is a full length card that holds the SSD much more securely than the short, connector-only adapters that many sellers are selling online. The best adapter currently available is the Sintech NGFF M.2 nVME SSD Adapter Card. The SSD connector on the MacBook Pro motherboard is not a standard NVMe interface, so you need an adapter. Original Apple drives are almost impossible to buy new, so you’re limited to buying used drives on sites like Ebay for inflated prices. They can be bought everywhere online or in IT stores. NVMe drives are much easier to source.Many of the current NVMe drives are faster than the stock Apple drives that shipped in the MacBook Pro.macOS versions from Mojave and later support NVMe drives as boot device in MacBook Pro models released from late 2013 to 2015 and MacBook Air models from 2013 to 2017.
#SSD FOR MAC AIR 2013 WINDOWS#
Original Apple SSD’s for the MacBook Pro and MacBook Air are very expensive, especially compared to the price of standard NVMe SSD’s designed for Windows PC’s. As an Amazon Associate I earn from qualifying purchases.
0 kommentar(er)
